Download Previous year Diploma Paper of Elements of Desgin 5th Sem Dec 2016 Automobile Diploma Paper
Elements of Desgin 5th Sem Dec 2016 Automobile Diploma Paper
                SECTION-A
Q1.Fill in the Blanks:- 1.5×10=15
a. The property of material to be drawn into wires is called _____________
b. Lack of ductility is called ____________
c. Rigid coupling is used to connect two shafts which are perfectly ___________
d __________ coupling is used to connect two shafts having both lateral and angular misalignment.
e. Clutch operates on principle of ____________
f. Clutch is also used to allow ___________ of gears when vehicle is running.
g. Flywheel is mounted on the ______________ of an engine.
h. A lap joint is always in ________ shear.
i. Power transmission by gear drive is called __________ drive.
j. Round key is also known as __________ key.
                 SECTION-B
Q2. Attempt any five questions.                                  5×6=30
a. Define the following properties: Elasticity, plasticity, and ductility.
b. What is design? Explain its necessity.
c. What is difference between clutch and coupling?
d. Define key. Explain its various types.
e. What is flywheel? Explain the function of flywheel and state its applications.
f. What is caulkimg and fullering process? Explain with help of diagram.
g. What are types of gears? Explain any three.
h. A steel plate 75 mm wide and 10 mm thick is welded to a plate with lap joint having transverse welding. Find size of weld if the load is 55 KN and allowable stress in tension = 100 N/mm2.
                SECTION-C
Q3. Attempt any three questions.                            3×10=30
1. Explain the design procedure.
2. Design a knuckle joint to transmit 150 KN. The design stress may be taken as 75 MPa in tension, 60 MPa in shear and 150 MPa in compression.
3. A solid steel shaft having ultimate shear stress 360 MPa and factor of safety as 8. It transmits 20 kW at 200 rpm. Find the diameter of the shaft. If the solid steel shaft is replaced with a hollow shaft, find its inside and outside diameter. The ratio of inside to outside diameter is taken as 0.5.
4. Design a flange coupling for a mild steel shaft transmitting 90 kW at 250 rpm. Allowable shear stress for mild steel = 40 MPa, for cast iron = 14 MPa and for bolt material = 30 MPa. The materials for shaft and key are same.
Elements of Desgin 5th Sem Dec 2016 Auto mobile Diploma Paper
Get StartedSection a Elements of Desgin 5th Sem Dec 2016 Automobile Paper
The property of material to be drawn into wires is called _____________The property of material to be drawn into wires is called _____________
Lack of ductility is called ____________
Rigid coupling is used to connect two shafts which are perfectly ___________
__________ coupling is used to connect two shafts having both lateral and angular misalignment.
Clutch operates on principle of ____________
Clutch is also used to allow ___________ of gears when vehicle is running.
Flywheel is mounted on the ______________ of an engine.
A lap joint is always in ________ shear.
Power transmission by gear drive is called __________ drive.
Round key is also known as __________ key.
Elements of Desgin 5th Sem Dec 2016 omobile Diploma Paper Click Here
Section B :Elements of Desgin 5th Sem dec 2016 Automobile Paper
Define the following properties: Elasticity, plasticity, and ductility.Properties: Elasticity, plasticity, and ductility.
Design and its necessity.
Difference between clutch and coupling.
Key and its various types.
Flywheel and function of flywheel and state its applications.
Caulkimg and fullering process.
Types of gears
Steel plate 75 mm wide and 10 mm thick is welded to a plate with lap joint having transverse welding. Find size of weld if the load is 55 KN and allowable stress in tension = 100 N/mm2.
Elements of Desgin 5th Sem Dec 2016 Automobile Diploma Paper Click Here
Elements of Desgin 5th Sem Dec 2016 Auto mobile Diploma Paper
Get Started https://www.youtube.com/watch?v=UHX6f8TIvX8https://www.youtube.com/watch?v=M_RR6LVICp0https://www.youtube.com/watch?v=mV41CMWonN4https://www.youtube.com/watch?v=s0LVPE0Q3LE&list=PLA9Q9SDZ781WXNAWit379A4CRLMvjGiUw&index=14&t=0sSection c :-Elements of Desgin 5th Sem dec 2016 Diploma Paper
Explain the design procedure.Design procedure.
A Design a knuckle joint to transmit 150 KN. The design stress may be taken as 75 MPa in tension, 60 MPa in shear and 150 MPa in compression.
Solid steel shaft having ultimate shear stress 360 MPa and factor of safety as 8. It transmits 20 kW at 200 rpm. Find the diameter of the shaft. If the solid steel shaft is replaced with a hollow shaft, find its inside and outside diameter. The ratio of inside to outside diameter is taken as 0.5.
Design a flange coupling for a mild steel shaft transmitting 90 kW at 250 rpm. Allowable shear stress for mild steel = 40 MPa, for cast iron = 14 MPa and for bolt material = 30 MPa. The materials for shaft and key are same.
Elements of Desgin 5th Sem Dec 2016 Automobile Diploma Paper Contact Us
MY YOUTUBE CHANNEL
JK Smart Classes Upload Lecture for Degree classes like B.TECH,M.TECH in any stream like ECE,EE,ME and Civil Engineering![\"JK](\"https://www.psbtepaper.com/wp-content/uploads/2020/03/JK-SMART-CLASSES-removebg-preview-1.jpg\")
JK SMART CLASSES
ER.JASWINDER KUMAR
JK SMART LECTURE
ER.JASWINDER KUMAR
Engineering Classes Upload Lecture for Polytechnic Diploma classes in any stream like ECE,EE,ME and Civil Engineering
ENGINEERING CLASSES
ER.JASWINDER KUMAR
er.jaswinder kumar
Senior Lecturer